Worked on this page for a good friend who has been generous with his time, etc., as I’ve fumbled through life as a brand-new General, then Amateur Extra, and Volunteer Examiner since last September or so… I know a bit about computers and he knows a *ton* about radio – believe me its worth my time. 🙂
I am drawing heavily on my previous post on the IC-718 radio, this copy will be tailored to the excellent Yeasu FT-950 radio. We tested this procedure on his rig, using an FTDI USB-serial cable. The rig defaults to 4800 baud, which we bumped up to 19200. It worked fine, he will let me know if it starts acting up at that speed, but tested for about half an hour and it was both fast and rock solid.
Unless you already have the appropriate cable for the FT-950, you will need to acquire one. If you are like me and have moved to newer laptop computers, you probably don’t have a true “Comm Port” on your computer and will need to pick up an appropriate FTDI USB-serial cable. (I am continuing to use another Ham operator’s eBay Store – BlueMax49ers – one whom I’ve had excellent results with in the past, solely as a customer/consumer – he hasn’t failed me yet).
Before we get started, lets have a look at the rig
I took a very hard look and a downloaded copy of the FT-950 Operating Manual – specifically for CAT-related items in the “Menu Mode”. Found the following to be on target:
Press the “MENU” button momentarily, to engage the Menu Mode.
Display will show the Menu Number, Menu Group Name, and Menu Item.
Press the “SELECT” knob momentarily to toggle the display between “Menu Number & Menu Group Name” and “Menu Item”. The Multi-Display Window shows the current setting of the currently selected Menu item.
Rotate the “SELECT” knob to select the menu item you wish to modify.
Rotate the “CLAR/VFO-B” knob to chnge the current setting of the selected Menu item.
Press the “CLEAR” button (located at the upper right of the “SELECT” knob momentarily to reset the selected Menu item to factory default value.
When you have finished making your adjustments, press and hold “MENU” button for one second to save the new setting and exit to normal operation. If you only momentarily press the “MENU” button, the new settings will NOT be retained.
Then I found the following CAT items:
O26 GENE CAT BPS – Default = 4800 bps (CAT data rate in baud) believe this should be set to 19200 for operation with a FTDI USB-serial Cable, but the default would probably be OK for a standard Comm port/cable
027 GENE CAT TOT – default = 10 msec TOT=time out timer
028 GENE CAT RTS – Default = On
SO – I suspect the only default menu item parameter that would need adjustment from the default setting would be the baud rate if you are using an FTDI USB-serial cable. Remember, to press and hold “MENU” button for one second after you have set the parameter to assure you actually SAVE the new setting.
Just a note, for CAT operation, I suspect you will want to have the radio in VFO mode rather than Memory… When it doubt, go for VFO.
The first step is to assure your Linux account has access to the serial ports:
Even if you are using an FTDI USB-serial cable purchased for the purpose – you still have to be in the appropriate Linux “group”… This is most important on any Debian/Ubuntu/Linux Mint installation as it is *not* a default group when you build your account(s).
Added my account name to the “dialout” group via Menu | Administration | Users and groups
Click on your account, then in the right click on the groups you are currently a member of – a list will pop-up and all you have to do is put a check mark next to the “dialout” group
Why the group name “dialout”? Every file in linux has a security setting for access in terms of read/write/execute “permissions”. You are either the owner, member of a group, or “other” – the owner of most things in the system is “root”, but you should never use root as your normal user within linux to avoid accidents and security problems. So – the next best thing is to be member of the group that has rights on the item you want to use. For instance, in this case we want to access/control the ttyUSBx port. (Probably ttyUSB0, [“zero”], but it may be 1, 2 or 3 depending upon your computer/peripherals).
Back in the ’80s and early ’90s, most of us hooked up a telephone modem, which is a serial device, so they named the group given control over serial devices “dialout”. Know it seems a weird name today, but that is how it came about and it still is in use. Adding your account to Group dialout will give you the desired rights/control over serial communication on Linux, including ttyUSBx (usually ttyUSB0).
Second Step – let’s download and install those “other” packages for associated software programs you may eventually want to use in conjunction with CQRLOG and get them set up to automatically get updated with system updates by enabling their PPA repositories where we can, that way they will be “ready” when you are.
Use Administration | Synaptic Package Manager to install the following:
In filter type xplanet and then select the xplanet and xplanet-images (Mark for install) go ahead and Apply (install).. Then delete the xplanet from filter box.
In left column click on Ham Radio Universe and mark the following for installation:
Chirp (if not already installed – very handy if you have a uhf/vhf radio – not applicable to CQRLOG)
FLdigi (if not already installed)
TrustedQSL (need this if you use Logbook of the World)
Go ahead and “Apply”/install the packages then close Synaptic Package Manager
Note: We skipped over wsjt – will get that later by other means rather than old package
Open a terminal – we will be installing PPA Updates one line at a time Terminal;
sudo rm -f /etc/apt/sources.list.d/ubuntu-hams-ppa-*
# type your password when prompted
sudo apt-add-repository ppa:ubuntu-hams-updates/ppa
# press ENTER when prompted
sudo apt-get update
# wait for the “$” prompt to reappear
That’s it, now Linux Mint will keep all your Ham Apps up to date automatically. You can refresh updates, and all the latest updates will be installed.
sudo add-apt-repository ppa:kamalmostafa/hamlib
# press ENTER when prompted
sudo apt-get update
# wait for the “$” prompt to reappear
Now for WSJTX: The version in the software center is way out of date, so you will want to add the PPA for this as well, If you already installed, no worry, this will update that version. Open termial, copy and paste: again one line at a time and hit enter, follow prompts.
sudo add-apt-repository ppa:ki7mt/wsjtx
sudo apt-get update
sudo apt-get install wsjtx
Now you will want to install the Encoder:
sudo add-apt-repository ppa:ki7mt/kvasd-installer
sudo apt-get update
sudo apt-get install kvasd-installer
– Open A terminal and type: kvasd-installer
– Then, select Install decoder from the menu.
If you have difficulty with WJSTx, as far as selecting the sound card, you will need to install this as well. Open Terminal:
sudo apt-get install libqt5multimediawidgets5 libqt5multimedia5-plugins
Note copied from K8WDX blog: Then set it up, and you should be good to go. more info on future releases can be found here: https://launchpad.net/~ki7mt I strongly suggest going to this site and reading through it, there are a couple of things to do to get the latest updates as well and info about the future of WJSTX. I just like to wait until the versions are out of the development stage before I take the plunge.
Third Step – if you haven’t already done so, let’s install the latest CQRLOG package:
A *very* good installation can be had with a single command in terminal mode:
sudo add-apt-repository ppa:ok2cqr/ppa;sudo apt-get update;sudo apt-get install cqrlog
That command, (described here for version 2.0.1-1), will first, add the ppa repository to your linux system’s list of authorized spots to check for updates, then update the system list itself, and finally install the latest version found in that repository.
OK, you can finally close terminal – open Update Manager, click on Refresh, then install any new packages it found. Because you added the PPAs above, Update Manager will check and install updates to your Ham programs.
Its finally time to run CQRLOG! (You will find it in your menu system, I recommend right-clicking on that menu item and pinning it to your panel). When the program opens you will see the “Database Connection” window, which contains a default log file #1 entry. Highlight that and click “Open”. The system “should” ask you to agree to download/install a couple of necessary databases – click Yes for each of them. (It will check for updates each time you open the program). The Database Connection window will close and the “New QSO” window will open.
In New QSO click on File | Preferences which will open the Preferences window to start your configuration of CQRLOG. Down the left side of Preferences is a vertical column of tabs which lead to pages of settings. I won’t cover all of them but here are my current recommendations for some of the more important stuff – you will have to play with them to suit your own desires – but pay particular attention to the TRX control stuff below:
- Select “Show statistics in” MHz if it isn’t already checked
- Select “Check for newer version of dxcc tables after program startup”
- Select “Check for newer version of qsl managers database after program startup”
- Select “Show distance in miles”
- Select “get UTC time from computer time
- Set “Grayline” to -1.25 (this setting worked for me on 05/24/2016)
- Set “Call” to your FCC approved Call Sign
- Set “Name” normally use your first name but…
- Set “QTH” to your home area, (i.e. San Diego County, CA)
- Set “Loc” to your Grid Square Locator (Hint – go here and type in your zip code if unsure) – This is a critical entry for the system to work correctly, make certain you have it right.
New QSO tab: (These are in addition to the defaults – some may now be new defaults in the latest version)
- For now, I left the “Default values” at the top alone, including “Comment for QSO”
- Also left “Enable auto mark QSO QSL_S field” as marked but with no value
- Set “Use spacebar to move between fields”
- Set “Skip over mode and frequency when radio is connected”
- Set “Enable autosearch on HamQTH.com/QRZ.com”
- Set “If ‘QSL via’ field contains other than a call sign, move to ‘Comment to QSO’ field”
- Set “Show recent QSO records for last” to 7 days (rather than 5)
- Set “In previous QSO list show QSO with call/p, call/m, W6/call etc.”
- Set “Always overwrite info from previous QSO with callbook data”
- Set “Always overwrite only CQ, ITU zones, County and US state”
- Set “Capitalise first letter in QTH field (yeah I know how to spell capitalize, but they are from Europe).
Visible Columns tab:
- Set “Date”
- Set “Time on”
- Set “CallSign” and “IOTA”
- Set “Mode”
- Set “Freq” and “QSL sent date”
- Set “RST sent”
- Set “RST Received” and DXCC
- Set “Name” and “Comment to QSO”
- Set “QTH” and “WAZ”
- Set “QSL sent”
- Set “QSL received”, “State”, and “Received QSL, LoTW, eQSL”
- Set “Country Name”
- Set each band you plan to use your rig on
TRX control tab:
- Set “Path to rigctl binary” to /usr/bin/rigctld
- Set “Radio one Desc.” to FT-950
- Set “Host” to localhost
- Set “Rig Model” to 128 Yaesu FT-950 (using the drop-down menu)
- Set “Device” to /dev/ttyUSB0 (that last character is a zero – need to verify yours may be 1, 2, 3, etc.)
- Set “Poll Rate” to 500
- Set “Port Number” to 4532
- Click to “X” Run rigctld when program starts
- For now, leave the rest at their default settings
You should not need any additional arguments added for rigctld. CQRLOG will start it with the rig model number – it looks like “rigctld -m 128”, (mine is -m 313 for my IC-718), and that automatically sets it up for that specific radio
ROT control tab:
- ***To be determined at a later date
- I would leave the defaults for this Yeasu rig – (note on ICOM radios for rig control the CQRLOG FAQ says to set them all to zero, and that works – but for ICOM rigs only)
QTH profiles tab:
- ***To be determined at a later date
- I set each and every item on this page – if I am “exporting” my log, I want *everything*.
- Colors are purely a personal decision – the darker colors generally work better for my eyes, but I wound up selecting Red, Lime, Blue and Navy respectively
- Set “Show only spots” to those freqs/bands you are interested in – mine currently spans from 1.8 MHz to 28 MHz
- Set “Show country name in the DX cluster spot”
- Set “Connect to DX cluster after program startup”
- I left this at defaults, (for now)
WAZ, ITU zones tab:
- Colors are purely a personal decision – I am currently using Red, Red, Blue, Blue, and Fuchsia, Fuchsia
- Set “Show info” for both WAZ and ITU
- I chose to set “New IOTA” to Red and QSL needed for IOTA to Blue
- Set “Show info”
- ***I haven’t set this up yet – not currently a member of anything associated with this
- Set “Use the same color as the spot
- Set “Ignore DX spots with freq equals to the start of the band (21.000, 14.000 etc., usually notes)”
- ***I will need to revisit this one later on
xplanet support tab:
- Set “Path for the xplanet” to /usr/bin/xplanet
- I set “‘Window size” to 340 x 340 for now, will revisit later
- Set “Show stations from” bandmap
- Set “Projection” to azimuthal without background
- Set “Use this xplanet font color” my selection was “White” by default, works well.
Zip code tracking tab:
- ***I left at default settings for now
LoTW/eQSL support tab:
- To use this tab, you will need an account with LoTW, (gained through TrustedQSL program), and register for an account on the eQSL web site. I have done so, but with LoTW – now waiting on a snail-mail card from ARRL telling me how to proceed. Note that part of this is to have a digital “certificate” file on your system to prove its actually “you” and your system doing the uploads to LoTW
- Set “Include LoTW and eQSL confirmed countries in DXCC statistic”
- Set “Use LoTW and eQSL confirmed countries for New country or New band etc. info”
- Set “Show info in New QSO window if station uses LoTW/eQSL
- Set “Use this color as a background in DX cluster and band map for stations using LoTW” (I chose Money Green)
- Set “Use this color as a background in DX cluster and band map for stations using eQSL” (I chose Sky Blue)
- Set “Upload to eQSL also data in COMMENT field”
CW interface tab:
- ***Left at defaults until I discuss this with a very experienced Elmer
fldigi/wsjt interface tab:
- ***Left at defaults until I have time to research this one
Auto backup tab: I consider this one to be IMPORTANT!
- Set “Enable autobackup after program ends
- Set “Save backup to:” using the browse button – mine worked out to be /home/dave/.config/cqrlog/database/
- Set “Backup file” by selecting “callsign, date and time (yourcall_yyyy-mm-dd_hh-mm-ss.adi)
- Set “Compress backup with tar.gz
External viewers tab:
- I left this one at defaults, it will probably stay that way for now
Callbook support tab:
- Set Callbook search to either your HamQTH account or QRZ account. Ham QTH is free – there is a minimal annual fee for QRZ – I elected to go with HamQTH for now – entering my User name and Password for that account in this tab
RBN support tab:
- Left “Server:” at the default telnet address and port – telnet.reversebeacon.net:7000 – for now, (but know my friend will want to change it to his favorite)
- Set “Login:” to your own callsign
- For now, I also set “Watch for:” to my own callsign
- Colors being subjective, I am using White, Purple, Maroon and Red in that order from the top down, (pretty sure these are now default colors)
- Set “Delete old information after” 180 seconds, (I’m getting older, the default 60 seconds was too fast)
Online log upload tab:
- Set “Enable upload to HamQTH” (if you have an account there)
- Set in your Username and Password for HamQTH
- I elected to “Set this” Blue “color to show information in status upload windowI left Clublog blank – not a member
- Set “Use this” Red “color to show information in status upload window” in case I use Clublog in future
- Left HRDLog.net entries blank
- Set “Use this” Purple “color to show information in status upload window” in case I use HRDLog in future
- Set “Show propagation as image
- I was not happy with the tiny default display, so changed “Download data from:” to http://www.hamqsl.com/solar101pic.php
- Set “Show A, K, SSN, FOF2 etc.”
- Set “Show calculated prediction for HF bands”
- Set “Show calculated prediction for VHF bands if you are interested
I will be counting on help about the rest of the settings from that same experienced Ham who has done many years of DX, and has experience with a different logging program. Between the two of us, we were able to whip his FT-950 into shape with CQRLOG, and in return, I will learn a ton about making effective *use* of it now that we both have rig control working.
A ton of credit for what you find on this page goes to K8WDX – his work, although on a previous version of CQRLOG and a different radio, inspired me to pursue installing everything needed now and for future work with those “other” digital modes. Many thanks to K8WDX for sharing his own experiences.
CQRLOG configure <–YouTube video on a previous version of CQRLOG also by K8WDX